|
Restor-A-Finish®
|
|
Restore
It - Don't Strip It!
|
 |
- Restores
original color and luster in wood finishes.
|
- Eliminates
white heat rings and water marks, scratches, smoke damage, sun
fade, and oxidation.
|
- Will NOT
dissolve the existing finish.
|
|
How
does it work?
|
Restor-A-Finish
is a unique finish-penetrating formula that restores the original color
and luster to your finish while blending out the blemishes and minor
scratches. Restor-A-Finish
cleans the surface and restores the finish in one step - without removing
any of the existing finish.
|
Restore
It - Don't Strip It!
|
With
a simple wipe-on, wipe-off process, most finished wood surfaces that seem
to need a refinishing job can be completely restored in a few minutes.
White heat rings and water marks, sun fade, oxidation, smoke damage, and
most other blemishes can be quickly eliminated. Before you go to the
extreme of stripping it, try restoring it!
Restor-A-Finish
is available in nine colors: Neutral, Maple-Pine, Golden Oak,
Cherry, Walnut, Mahogany, Dark Walnut, Dark Oak, and Ebony Brown. |
| Neutral |
Maple-Pine |
Golden
Oak |
| Cherry |
Walnut |
Mahogany |
| Dark
Walnut |
Dark
Oak |
Ebony
Brown |
|
Treat
Scratches, Nicks, and Abrasions
|
Restor-A-Finish
works best when applied with a small pad of toweling, or for severe white
rings and crazing, with Super Fine(0000) steel wool. DO NOT pour
directly on the finish. When using steel wool, always rub with the
grain of the wood. First, determine the pressure you should use on
an inconspicuous spot, as the hardness of finishes vary.
|
White
Heat Rings and Water and Smoke Damage
|
Apply Restor-A-Finish
(see above) with steel wool and rub hard enough with the grain of the wood
to blend out the white effect. If high gloss finish should appear
dull due to the use of steel wool, polish it out with a commercial
polishing compound.
|
Revive
Wood Finishes
|
Wipe
on the appropriate color of Restor-A-Finish
with a clean cloth. Let it stand for a few minutes then wipe dry.
If you desire a darker shade, simply apply a darker color of Restor-A-Finish.
|
Raised
and Blistered Finishes
|
Apply
Neutral Restor-A-Finish
(to prevent darkening of wood beyond temporary "wet effect")
with steel wool. As blisters soften press down, press down as Restor-A-Finish
is applied. Wipe
dry, and again later if the surface "blooms" with excess Restor-A-Finish.
|
Restore
Minor Crazed or Checked Finishes
|
Apply
Restor-A-Finish with
Medium Grade(00) steel wool. Rub hard enough to smooth out the
finish, periodically checking your progress. Checked or crazed
surfaces may absorb an excess of Restor-A-Finish
and "bloom out" requiring another wiping later.
|
Treat
Carved Wood
|
Restor-A-Finish
has saved many hours of labor by chemically cleaning and restoring the
finish on carved portions of furniture and clocks. Simply apply
Restor-A-Finish
with a small paint brush or soft tooth brush and wipe off.
|
Tips
|
Be
careful to protect fabric, carpets, and linoleum when applying Restor-A-Finish.
It may leave a permanent stain. If spilling occurs, immediately
scrub areas with straight liquid detergent or stain remover and wipe dry.
Be sure to cover a small area at a time when applying Restor-A-Finish.
Always wipe dry. DO NOT apply Restor-A-Finish
to the new imitation wood finishes or use it under polyurethane finishes
as a stain!
|